CrossfireForum - The Chrysler Crossfire and SRT6 Resource

Troubleshooting & Technical Questions & Modifications Have technical or modification questions about the Crossfire? Find out the answer, or give advice in here!

skreem module

Thread Tools
 
  #21 (permalink)  
Old 09-02-2019, 01:28 PM
Join Date: Jun 2017
Location: New Jersey
Age: 63
Posts: 22
Likes: 0
Received 0 Likes on 0 Posts
Default Re: skreem module


The code is P0410 Secondary Air injection system generic pending

P0410 generic current Secondary Air Injection system

Honestly don’t know what this means
 
Reply Like
  #22 (permalink)  
Old 09-02-2019, 01:41 PM
Toolman's Avatar
Senior Member
Join Date: Feb 2009
Location: Philadelphia, PA
Posts: 1,002
Received 54 Likes on 43 Posts
Default Re: skreem module
The computer is not seeing the air injector pump running at start up. Try cleaning the contacts on the pump connector as well as the ground wire on it.
 
Reply Like
  #23 (permalink)  
Old 09-02-2019, 01:45 PM
Join Date: Jun 2017
Location: New Jersey
Age: 63
Posts: 22
Likes: 0
Received 0 Likes on 0 Posts
Default Re: skreem module
Thanks for the reply but I would have no idea where the contacts are. Can you point me in the right direction
 
Reply Like
  #24 (permalink)  
Old 09-02-2019, 02:09 PM
Toolman's Avatar
Senior Member
Join Date: Feb 2009
Location: Philadelphia, PA
Posts: 1,002
Received 54 Likes on 43 Posts
Default Re: skreem module
Here is a picture of the secondary air injector. The connector is on the far right and the torx ground screw is shown to the left of that.

 
Reply Like
  #25 (permalink)  
Old 09-02-2019, 02:18 PM
Join Date: Jun 2017
Location: New Jersey
Age: 63
Posts: 22
Likes: 0
Received 0 Likes on 0 Posts
Default Re: skreem module
Thanks for the picture, I cleaned both contacts with a wire brush. What are the next steps? Do I clear the code and see if it cycles and stays off.
 
Reply Like
  #26 (permalink)  
Old 09-02-2019, 02:24 PM
Toolman's Avatar
Senior Member
Join Date: Feb 2009
Location: Philadelphia, PA
Posts: 1,002
Received 54 Likes on 43 Posts
Default Re: skreem module
Originally Posted by allyn
Thanks for the picture, I cleaned both contacts with a wire brush. What are the next steps? Do I clear the code and see if it cycles and stays off.
Yes,

BTW, for the ground contact you have to remove the screw and clean the connector itself, and the spot where it screws into.
 
Last edited by Toolman; 09-02-2019 at 02:27 PM.
Reply Like
  #27 (permalink)  
Old 09-02-2019, 02:42 PM
Join Date: Jun 2017
Location: New Jersey
Age: 63
Posts: 22
Likes: 0
Received 0 Likes on 0 Posts
Default Re: skreem module
Check engine light is off and hopefully I am good to go. Thanks for all your help and sorry to bother you on Labor Day. Hope you have a great rest of your day.
 
Reply Like
  #28 (permalink)  
Old 09-02-2019, 02:44 PM
Join Date: Jun 2017
Location: New Jersey
Age: 63
Posts: 22
Likes: 0
Received 0 Likes on 0 Posts
Default Re: skreem module
And yes I removed the screw and cleaned the connector and base it is screwed too. Thanks again
 
Reply Like
  #29 (permalink)  
Old 09-02-2019, 03:11 PM
Valk's Avatar
Administrator / Senior Member
Join Date: Jul 2007
Location: Aurora , ILL
Posts: 17,332
Received 629 Likes on 430 Posts
Default Re: skreem module
P410 code is not at all important
Just annoying that the CEL comes on
It's an emissions air pump and many things can trigger the light even when he pump is working
 
Reply Like
  #30 (permalink)  
Old 09-02-2019, 03:58 PM
onehundred80's Avatar
Senior Member
Join Date: Apr 2006
Location: Ontario
Age: 84
Posts: 25,429
Received 610 Likes on 510 Posts
Default Re: skreem module
Originally Posted by Valk
P410 code is not at all important
Just annoying that the CEL comes on
It's an emissions air pump and many things can trigger the light even when he pump is working
It could be a problem if the pump does not switch OFF. The pump would then self destruct in a short period of time, I do not know offhand if there is a specific code for that eventuality though.
 
Reply Like
  #31 (permalink)  
Old 09-02-2019, 04:22 PM
Join Date: Jun 2017
Location: New Jersey
Age: 63
Posts: 22
Likes: 0
Received 0 Likes on 0 Posts
Default Re: skreem module
I’ll keep an eye on it
 
Reply Like
  #32 (permalink)  
Old 09-03-2019, 09:08 PM
Join Date: Jun 2017
Location: New Jersey
Age: 63
Posts: 22
Likes: 0
Received 0 Likes on 0 Posts
Default Re: skreem module
Update: threw around 80 miles on the car today. CEL is still off. Hopefully I am good to go.
 
Reply Like
  #33 (permalink)  
Old 09-04-2019, 07:42 AM
Toolman's Avatar
Senior Member
Join Date: Feb 2009
Location: Philadelphia, PA
Posts: 1,002
Received 54 Likes on 43 Posts
Default Re: skreem module
Originally Posted by allyn
Update: threw around 80 miles on the car today. CEL is still off. Hopefully I am good to go.
Very good to hear.
 
Reply Like
  #34 (permalink)  
Old 09-12-2019, 11:25 AM
Join Date: Jun 2017
Location: New Jersey
Age: 63
Posts: 22
Likes: 0
Received 0 Likes on 0 Posts
Default Re: skreem module
Update the CEL came on again yesterday, did not check the code. I had the refurbished RCM in the car, so I replaced it with the new one I purchased a month or so back and the CEL went off. Will continue to monitor. 🤷🏻*♂️
 
Reply Like
  #35 (permalink)  
Old 09-12-2019, 06:16 PM
pizzaguy's Avatar
Administrator
Join Date: Jun 2009
Location: Fort Worth, Texas
Age: 64
Posts: 13,569
Received 965 Likes on 752 Posts
Default Re: skreem module
Originally Posted by allyn
Update the CEL came on again yesterday, did not check the code.
That is like picking out a nice new shirt wearing a blindfold.
 
Reply Like
  #36 (permalink)  
Old 09-12-2019, 06:29 PM
Join Date: Jun 2017
Location: New Jersey
Age: 63
Posts: 22
Likes: 0
Received 0 Likes on 0 Posts
Default Re: skreem module
If the CEL comes on again I’ll check the code
 
Reply Like
  #37 (permalink)  
Old 09-12-2019, 07:03 PM
Join Date: Jun 2017
Location: New Jersey
Age: 63
Posts: 22
Likes: 0
Received 0 Likes on 0 Posts
Default Re: skreem module
Switched the RCM and CEL went off
 
Reply Like
  #38 (permalink)  
Old 10-07-2019, 09:02 AM
phil alvirez's Avatar
Senior Member
Join Date: Jun 2019
Location: windsor ontario next to detroit
Posts: 1,047
Received 37 Likes on 30 Posts
Default Re: skreem module
Originally Posted by papajerry
FYI, I have an account with Mercedes and spoke to there parts department about getting a module from them. They have 600 in available, but will not sell them except for a Mercedes. The list price is $270.00 for the module. The local Chrysler Dealer told me they are working on a supplier,hopefully by Oct. 15th but do not expect them to be available before December. Chrysler list is $577.00.
I would also like to have a spare one just in case.
i would like to understand what do you get if you have 1
suppose you can get the module from mercedes. just suppose. what then? what about the match with the VIN? how can it be used with a croosie? what you have to do to have it replacing the 1 you have? programming? how? who has the knowledge and the tools to do that?
thanks
 
Reply Like
  #39 (permalink)  
Old 10-08-2019, 04:30 AM
Join Date: Aug 2017
Location: Germany
Age: 57
Posts: 208
Received 40 Likes on 25 Posts
Default Re: skreem module
Originally Posted by phil alvirez
i would like to understand what do you get if you have 1
suppose you can get the module from mercedes. just suppose. what then? what about the match with the VIN? how can it be used with a croosie? what you have to do to have it replacing the 1 you have? programming? how? who has the knowledge and the tools to do that?
thanks
The Skreem Modul from Mercedes (also it is the same Part Number) would not work in the Crossfire, The ROM in the Prozessor is different to the Skreem Modul of the Crossfire. And also if you buy a Skreem from Chrysler it has to be programmed to your car. A not programmed new modul is as useless as every used modul from an other Crossfire.
 
Reply Like
  #40 (permalink)  
Old 10-08-2019, 04:41 AM
phil alvirez's Avatar
Senior Member
Join Date: Jun 2019
Location: windsor ontario next to detroit
Posts: 1,047
Received 37 Likes on 30 Posts
Default Re: skreem module
bad news, but at least now we know. thank you very much for telling. this puts an end to that search. it is better to know the truth than having false hopes.
o well...
 
Reply Like



Advanced Search
Quick Reply: skreem module


Reply Closed Thread Share

All times are GMT -4. The time now is 08:49 AM.