FEELER: SRT-6.com groupbuy ViS Racing carbon fiber hood for $500-$650 USD
Re: FEELER: SRT-6.com groupbuy ViS Racing carbon fiber hood for $500-$650 USD
My CF hood came with a CF front Chrysler wing with space in the middle for an emblem.. does the stock wing/emblem have tabs on the back for mounting or is it just held on by double sided tape? something to think about..
also, I still like the firepower design, a cowl or scoop in the middle is a little excessive though. If you're going to deviate and put vents farther up the hood, might I suggest taking a page from our SLK brethren?
Note the "matching" 3 strakes..
also, I still like the firepower design, a cowl or scoop in the middle is a little excessive though. If you're going to deviate and put vents farther up the hood, might I suggest taking a page from our SLK brethren?
Note the "matching" 3 strakes..
We will NOT make a cf emblem incorporated in the cf hood. The OEM emblem will be used. So some small holes will be needed to drill and or use adhesive.
Re: FEELER: SRT-6.com groupbuy ViS Racing carbon fiber hood for $500-$650 USD
Ok I will put you down as interested. Everytime I go out and take a look at the car I can see the waldig design work. anything else just looks silly. Just writing my thoughts as I need to wait 30 seconds until next post..
Re: FEELER: SRT-6.com groupbuy ViS Racing carbon fiber hood for $500-$650 USD
When design is ready
I do a new list where everyone interested must send me their details and agree with the approximately final design, that maybe hood pins may be necessary, and other factors that I have not come up with yet. Me and Fred at ViS have conversations daily and we are setting up a date where I am sending a car with DCAI so they can measure for clearance.
Just stay tuned and we will get this going.
I do a new list where everyone interested must send me their details and agree with the approximately final design, that maybe hood pins may be necessary, and other factors that I have not come up with yet. Me and Fred at ViS have conversations daily and we are setting up a date where I am sending a car with DCAI so they can measure for clearance.
Just stay tuned and we will get this going.
Re: FEELER: SRT-6.com groupbuy ViS Racing carbon fiber hood for $500-$650 USD
Here is a thought and design.
Note that the rear is no scoop, it is an airvent. see explanation pic next.
7-mid-look.jpg
Explanation
7-mid-explain.jpg
The waldig design without spine in the middle. The spine looks good on computer. But I just cannot see it when I stand next to Albino. It looks strange...
7-without-dark.png
Note that the rear is no scoop, it is an airvent. see explanation pic next.
7-mid-look.jpg
Explanation
7-mid-explain.jpg
The waldig design without spine in the middle. The spine looks good on computer. But I just cannot see it when I stand next to Albino. It looks strange...
7-without-dark.png
Re: FEELER: SRT-6.com groupbuy ViS Racing carbon fiber hood for $500-$650 USD
Just been out checking the car. IRL the vent must try to start as high up as possible and have a small angle slant. Then it will look good. So start as high up as possible towards the windscreen. maybe mid of hood.
Spine is just about taste. But it is coming more and more towards the waldig one but with minor enhancements that the ViS designers will do.
Clean Waldig
blue.png
Waldig with spine
blue-with-spine-in-vent.png
Spine is just about taste. But it is coming more and more towards the waldig one but with minor enhancements that the ViS designers will do.
Clean Waldig
blue.png
Waldig with spine
blue-with-spine-in-vent.png
Re: FEELER: SRT-6.com groupbuy ViS Racing carbon fiber hood for $500-$650 USD
So here are two of to close to final designs. This is waldig with or without spines.
Photo 2013-11-26 23 12 50.jpg
Photo 2013-11-26 23 13 21.jpg
Photo 2013-11-26 23 12 50.jpg
Photo 2013-11-26 23 13 21.jpg
Last edited by FUBU; 11-26-2013 at 05:18 PM.
Re: FEELER: SRT-6.com groupbuy ViS Racing carbon fiber hood for $500-$650 USD
With rounded edges as asked for.
Photo 2013-11-26 23 56 31.jpg
How many would feel comfortable with something like this?
Photo 2013-11-26 23 56 31.jpg
How many would feel comfortable with something like this?
Re: FEELER: SRT-6.com groupbuy ViS Racing carbon fiber hood for $500-$650 USD
Here is a thought and design.
Note that the rear is no scoop, it is an airvent. see explanation pic next.
Attachment 30106
Explanation
Attachment 30105
The waldig design without spine in the middle. The spine looks good on computer. But I just cannot see it when I stand next to Albino. It looks strange...
Attachment 30107
Note that the rear is no scoop, it is an airvent. see explanation pic next.
Attachment 30106
Explanation
Attachment 30105
The waldig design without spine in the middle. The spine looks good on computer. But I just cannot see it when I stand next to Albino. It looks strange...
Attachment 30107
Re: FEELER: SRT-6.com groupbuy ViS Racing carbon fiber hood for $500-$650 USD
Remember, these are just mockups for the ViS guys too see. So clearance and other stuff may change the final design. But this is the idea they will use when they start. It is a Waldig + Firepower = SRT-6.com design. Tried my best to make it look good. and as deep as possible the vent will be so it also will be functional.
Re: FEELER: SRT-6.com groupbuy ViS Racing carbon fiber hood for $500-$650 USD
With rounded edges as asked for.
Attachment 30116
How many would feel comfortable with something like this?
Attachment 30116
How many would feel comfortable with something like this?
Take a closer look to the latest design. It is what you are after.
Attachment 30117
It has spine
Long slanted vents
Rounded edges
Attachment 30117
It has spine
Long slanted vents
Rounded edges