Fun with decals on the third brake light.
Re: Fun with decals on the third brake light.
~ i spoke with the graphic company and they don't offer anything with less adhesion.
Re: Fun with decals on the third brake light.
~ opps ... you received the roadster by error. i will resend you the coupe design on monday ... sorry for the mix up.
Re: Fun with decals on the third brake light.
No problem Andrew. If you don't mind just send a roadster instead ( red or blue ), I'll be just as happy! It will fit then.
Re: Fun with decals on the third brake light.
~ it appears i was given the wrong measurements for the coupe size decal ... can one please give me the correct measurement so i can produce the right size and resend the corrected size to coupe buyers?
thanks,
andrew
thanks,
andrew
Last edited by andrew; 02-26-2013 at 09:02 AM.
Re: Fun with decals on the third brake light.
So basically, I have R O S S F I R when brake light is lit.
My bad, so sorry.
Please correct before sending anyone else a roadster decal,
I don't deserve one due to my stupidity.
Re: Fun with decals on the third brake light.
Here are all the measurements. Thanks for the great install instructions with the trim. Extremely easy!
Andrew, what is the possibility of getting a sticker that is the negative of the letters (leaves everything blacked out except the letters) letting the light show through CROSSFIRE? Also if the sticky stuff is on the face of the letters it can be stuck to the inside of the glass of the back hatch and the third LED housing will bolt right up against it. I would REALLY like the sticker this way if possible. The sticker would then be a little larger since the glass is at a angle instead of the very skinny third brack light which will be really hard to install and not have as neat of an effect like up against the glass.
The LED plastic housing is 7/16" in height and 11 13/16" in length.
The glass opening is 1 7/8" in height and 11 5/8" in length.
IMG_2944_zps73b47ac2.jpg
IMG_2947_zps9f895026.jpg
IMG_2953_zps92303265.jpg
IMG_2952_zps4822f945.jpg
IMG_2951_zpsd4699411.jpg
IMG_2928_zpsb1accdbc.jpg
Andrew, what is the possibility of getting a sticker that is the negative of the letters (leaves everything blacked out except the letters) letting the light show through CROSSFIRE? Also if the sticky stuff is on the face of the letters it can be stuck to the inside of the glass of the back hatch and the third LED housing will bolt right up against it. I would REALLY like the sticker this way if possible. The sticker would then be a little larger since the glass is at a angle instead of the very skinny third brack light which will be really hard to install and not have as neat of an effect like up against the glass.
The LED plastic housing is 7/16" in height and 11 13/16" in length.
The glass opening is 1 7/8" in height and 11 5/8" in length.
IMG_2944_zps73b47ac2.jpg
IMG_2947_zps9f895026.jpg
IMG_2953_zps92303265.jpg
IMG_2952_zps4822f945.jpg
IMG_2951_zpsd4699411.jpg
IMG_2928_zpsb1accdbc.jpg
Last edited by JesseJamessrt6; 02-26-2013 at 08:09 PM.
Re: Fun with decals on the third brake light.
The only with the glass decal is that it might not look right from car height eye level from behind. I already bought a can of lens tint so either way is actually fine. I'm sure you have already lost your butt on this project, so tell me what you can do either way. I will purchase the new style.
Re: Fun with decals on the third brake light.
~ jesse thank you for taking the time and sending the exact measurements ~ let me see what i do...
Thread
Thread Starter
Forum
Replies
Last Post
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)