Help With Installing New Tranny Plug Connector
Help With Installing New Tranny Plug Connector
Thanks to everyone's help here, I have successfully installed a new conductor plate and sensors to address my limp mode issue. I am at the end and am having the darnedest time putting back the new connector for the tranny plug. For the life of me I cannot get the center 7 mm bolt to catch. Am I supposed to push the connector all the way down into the housing or what. I am stuck here. IS THERE A certain alignment of the pin holes. I am at a loss here and the is the only thing holding me up in finishing the job. I saw where you wrestlers with this and any assistance you can provide will be a great help.
I guess the main thing I need to know is there a certain alignment of the pins to holes that I should be following and am I supposed to be pushing the connector all the way down into the hole.
I have been really struggling with this as everything else went fine in changing the conductor plate. I just cannot simply install my new connector for the tranny plug.
I guess the main thing I need to know is there a certain alignment of the pins to holes that I should be following and am I supposed to be pushing the connector all the way down into the hole.
I have been really struggling with this as everything else went fine in changing the conductor plate. I just cannot simply install my new connector for the tranny plug.
Re: Help With Installing New Tranny Plug Connector
ala_xfire:
I will tell you that the previous video you sent me in a prior thread was dead on point and helped me easily change the conductor plate with no issues. I followed the video step by step and it made the job very easy. I cannot now believe putting this connector cap back on for the tranny plug is holding me up from completing the job
I will tell you that the previous video you sent me in a prior thread was dead on point and helped me easily change the conductor plate with no issues. I followed the video step by step and it made the job very easy. I cannot now believe putting this connector cap back on for the tranny plug is holding me up from completing the job
Re: Help With Installing New Tranny Plug Connector
ala_xfire:
I will tell you that the previous video you sent me in a prior thread was dead on point and helped me easily change the conductor plate with no issues. I followed the video step by step and it made the job very easy. I cannot now believe putting this connector cap back on for the tranny plug is holding me up from completing the job
I will tell you that the previous video you sent me in a prior thread was dead on point and helped me easily change the conductor plate with no issues. I followed the video step by step and it made the job very easy. I cannot now believe putting this connector cap back on for the tranny plug is holding me up from completing the job
This is to found in my thread "Index of Crossfire ....." in my signature.
Last edited by onehundred80; 01-04-2020 at 10:56 AM.
Re: Help With Installing New Tranny Plug Connector
The instructions to put the pilot bushing back are halfway down this article. CLICK
This is to found in my thread "Index of Crossfire ....." in my signature.
This is to found in my thread "Index of Crossfire ....." in my signature.
Thanks so much to all for your assistance
Williams
Re: Help With Installing New Tranny Plug Connector
Okay I have watched all of the videos and done all of the research on installing this electrical tranny plug and so I know I am doing it correct after watching over 20 videos But for the life of me no matter how much I coat the new connector with tranny oil I cannot get it to push all the way into the cavity. Is there some other lubricant you guys can suggest. I know not to use grease as that will compromise the rubber gaskets.
I have where other forum members struggled t get the connector seated or pushed all the way in. Any suggestions would really help
I have where other forum members struggled t get the connector seated or pushed all the way in. Any suggestions would really help
Thread
Thread Starter
Forum
Replies
Last Post
Sadjetsfan
Troubleshooting & Technical Questions & Modifications
3
12-08-2013 10:38 AM
MikeR
Engine, Exhaust, Transmission and Differential
4
03-18-2009 02:19 PM
tylerxfire
Engine, Exhaust, Transmission and Differential
8
04-22-2008 05:05 PM
roms33
Troubleshooting & Technical Questions & Modifications
4
10-04-2004 12:39 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)