What did you do to your Crossfire today?
The following users liked this post:
×Crossfire1× (09-23-2023)
Re: What did you do to your Crossfire today?
Re: What did you do to your Crossfire today?
Last edited by dcskmail; 05-12-2023 at 09:34 AM.
The following users liked this post:
WD40 (05-13-2023)
Re: What did you do to your Crossfire today?
Picked it up from the shop where they replaced the washer reservoir. Cannot overstate the benefits of being able to clean the windshield when needed. Put on the interior cover/tonneau cover, fits nicely, looks good, and it fits easily into the gear bag in the trunk. We have a date with some bug remover in a little while.
Re: What did you do to your Crossfire today?
Used a 3M headlight restoration kit to make my headlights look brrand new. I have not driven at night yet, so I havn't seen the improvement yet in headlight brightness.
And yes, there is an "easter egg" in that photo. I did not notice myself until after I used the kit.
The following 3 users liked this post by findRED:
Re: What did you do to your Crossfire today?
That kit is the one I use & always get great results. Headlight lense looks great! Nice Job!
Re: What did you do to your Crossfire today?
Hey all, Today I removed both seats, vac'd the interior and then partially installed harnesses (side mounted each side), the rear mounts in the boot space I haven't cemented a plan for as yet...
Time will tell (roadtest) if I need to swap out the factory seats for aftermarket buckets in order for harnesses to safely work (not for track just aesthetics - daft I know).
More black leather with yellow stitch items on route to cover the back pillar, door handles etc etc.
Time will tell (roadtest) if I need to swap out the factory seats for aftermarket buckets in order for harnesses to safely work (not for track just aesthetics - daft I know).
More black leather with yellow stitch items on route to cover the back pillar, door handles etc etc.
The following 2 users liked this post by Ljcollingham:
anglefury21 (05-18-2023),
M60A3Driver (06-15-2023)
Re: What did you do to your Crossfire today?
I went and changed out the faded emblem on the hood. Rarely do I see a Crossfire that has anything but a faded front emblem on the cars given the age.
So I bought one on eBay and found the easiest way to is to just take a drill bit and drill right where the RY of CHRYSLER is. Don't drill too deep but don't worry it's hollow behind there..
Then you can take a screw driver and just peel off the rest of the old emblem. I then used some rubbing alcohol and Goo-Gone to clean the area.
New emblem had doubled sided tape but I found it wouldn't fit with the tape and also wasn't sure if it holds up in the sun.
Ended up using a silicone adhesive and just placed the new emblem. Was super quick and looks beautiful.
Now if I could only find one that fits the trunk. So far the trunk would need the whole wing replaced. Those are readily available and are just glued in also. But the emblem is smaller so not sure if I can ever find that one.
Good news is that one is in pretty great shape cause the SRT wing gives it shade lol.
So I bought one on eBay and found the easiest way to is to just take a drill bit and drill right where the RY of CHRYSLER is. Don't drill too deep but don't worry it's hollow behind there..
Then you can take a screw driver and just peel off the rest of the old emblem. I then used some rubbing alcohol and Goo-Gone to clean the area.
New emblem had doubled sided tape but I found it wouldn't fit with the tape and also wasn't sure if it holds up in the sun.
Ended up using a silicone adhesive and just placed the new emblem. Was super quick and looks beautiful.
Now if I could only find one that fits the trunk. So far the trunk would need the whole wing replaced. Those are readily available and are just glued in also. But the emblem is smaller so not sure if I can ever find that one.
Good news is that one is in pretty great shape cause the SRT wing gives it shade lol.
The following users liked this post:
M60A3Driver (06-15-2023)
Re: What did you do to your Crossfire today?
I've had these Crossfire replacement emblems on my car for 4 years still look new. wheel caps, front/rear key fob, steering wheel etc. Coupe or roadster design , they may also have the Chrysler logo
https://beststickers.net/index.php?r...product_id=817
Last edited by dcskmail; 05-19-2023 at 11:47 AM.
The following users liked this post:
M60A3Driver (06-15-2023)
Re: What did you do to your Crossfire today?
I've had these Crossfire replacement emblems on my car for 4 years still look new. wheel caps, front/rear key fob, steering wheel etc. Coupe or roadster design , they may also have the Chrysler logo
https://beststickers.net/index.php?r...product_id=817
https://beststickers.net/index.php?r...product_id=817
Join Date: Oct 2012
Location: Waterloo, Ontario
Age: 67
Posts: 325
Likes: 0
Received 1 Like
on
1 Post
The following users liked this post:
M60A3Driver (06-15-2023)
The following users liked this post:
M60A3Driver (06-15-2023)
Re: What did you do to your Crossfire today?
I went and changed out the faded emblem on the hood. Rarely do I see a Crossfire that has anything but a faded front emblem on the cars given the age.
So I bought one on eBay and found the easiest way to is to just take a drill bit and drill right where the RY of CHRYSLER is. Don't drill too deep but don't worry it's hollow behind there..
Then you can take a screw driver and just peel off the rest of the old emblem. I then used some rubbing alcohol and Goo-Gone to clean the area.
New emblem had doubled sided tape but I found it wouldn't fit with the tape and also wasn't sure if it holds up in the sun.
Ended up using a silicone adhesive and just placed the new emblem. Was super quick and looks beautiful.
Now if I could only find one that fits the trunk. So far the trunk would need the whole wing replaced. Those are readily available and are just glued in also. But the emblem is smaller so not sure if I can ever find that one.
Good news is that one is in pretty great shape cause the SRT wing gives it shade lol.
So I bought one on eBay and found the easiest way to is to just take a drill bit and drill right where the RY of CHRYSLER is. Don't drill too deep but don't worry it's hollow behind there..
Then you can take a screw driver and just peel off the rest of the old emblem. I then used some rubbing alcohol and Goo-Gone to clean the area.
New emblem had doubled sided tape but I found it wouldn't fit with the tape and also wasn't sure if it holds up in the sun.
Ended up using a silicone adhesive and just placed the new emblem. Was super quick and looks beautiful.
Now if I could only find one that fits the trunk. So far the trunk would need the whole wing replaced. Those are readily available and are just glued in also. But the emblem is smaller so not sure if I can ever find that one.
Good news is that one is in pretty great shape cause the SRT wing gives it shade lol.