What did you do to your Crossfire today?
Re: What did you do to your Crossfire today?
[QUOTE=UrbanE;977175]I dropped mine off to my bodyshop. Hope it goes well!
The following users liked this post:
CaughtInaXF (03-11-2023)
Re: What did you do to your Crossfire today?
REAR DIFFUSERS
A woman in Poland on a Crossfire Facebook page posted a pic of her Crossfire with rear Diffusers that she made at a company she works with in Poland
They are made using ABS material.
She did it by thermoforming. They have the equipment because they do similar projects.
Many of us have gotten these within 1 week from Poland to various states is the US
If you use Facebook message Anna Malik to get more info if ya want set of these.
If you dont use Facebook you can send an email to the seller at: ana1330@interia.pl
Her name is Ana Malik and your email can let her know you saw these posted on the Crossfire Forum
I don't believe she is a member here yet though
A woman in Poland on a Crossfire Facebook page posted a pic of her Crossfire with rear Diffusers that she made at a company she works with in Poland
They are made using ABS material.
She did it by thermoforming. They have the equipment because they do similar projects.
Many of us have gotten these within 1 week from Poland to various states is the US
If you use Facebook message Anna Malik to get more info if ya want set of these.
If you dont use Facebook you can send an email to the seller at: ana1330@interia.pl
Her name is Ana Malik and your email can let her know you saw these posted on the Crossfire Forum
I don't believe she is a member here yet though
Re: What did you do to your Crossfire today?
REAR DIFFUSERS
A woman in Poland on a Crossfire Facebook page posted a pic of her Crossfire with rear Diffusers that she made at a company she works with in Poland
They are made using ABS material.
She did it by thermoforming. They have the equipment because they do similar projects.
Many of us have gotten these within 1 week from Poland to various states is the US
If you use Facebook message Anna Malik to get more info if ya want set of these.
If you dont use Facebook you can send an email to the seller at: ana1330@interia.pl
Her name is Ana Malik and your email can let her know you saw these posted on the Crossfire Forum
I don't believe she is a member here yet though
A woman in Poland on a Crossfire Facebook page posted a pic of her Crossfire with rear Diffusers that she made at a company she works with in Poland
They are made using ABS material.
She did it by thermoforming. They have the equipment because they do similar projects.
Many of us have gotten these within 1 week from Poland to various states is the US
If you use Facebook message Anna Malik to get more info if ya want set of these.
If you dont use Facebook you can send an email to the seller at: ana1330@interia.pl
Her name is Ana Malik and your email can let her know you saw these posted on the Crossfire Forum
I don't believe she is a member here yet though
I believe the OEM ones had the hole. ABS is the best plastic for this kind of accessory. Fibre glass is too brittle.
The following users liked this post:
CaughtInaXF (03-11-2023)
The following users liked this post:
CaughtInaXF (03-11-2023)
The following users liked this post:
WD40 (03-10-2023)
The following users liked this post:
CaughtInaXF (03-11-2023)
Re: What did you do to your Crossfire today?
Exhaust tips ?
Re: What did you do to your Crossfire today?
did front calipers on our 05 crossfire. Caliper heat paint with new rotors & Pads. Came out pretty good
The following users liked this post:
CaughtInaXF (03-11-2023)
Re: What did you do to your Crossfire today?
I'm gonna drill a small whole in each fin
I contacted the seller and she is aware hers have no holes but she leaves it for the buyer to decide if they wish to have them or not
Re: What did you do to your Crossfire today?
So are you guys talking about locating a drain hole in the bottom of the fins? I see where the Seller locates dimples for the mounting holes in the diffusers. Couldn't see any harm or impact if she did the same on the bottom of the fins.
Last edited by dedwards0323; 03-10-2023 at 04:58 PM.
Re: What did you do to your Crossfire today?
I replied "Might be a suggestion you add on a piece of paper with each shipment"
Re: What did you do to your Crossfire today?
Bought new (to me) valve cover$.
Cleaned, sanded, filled, primed and painted/cleared.
Installed with new gaskets, hoses and hardware(from NeedsWings).
Torqued inside out pattern from 7 to 8ft/lbs.
No leakage and looks hawt!
Enjoy your weekend and your XF!
Thanks to Rob at NeedsWings for hardware
Shine and sparkle of fresh valve covers is outstanding
Cheers!
Cleaned, sanded, filled, primed and painted/cleared.
Installed with new gaskets, hoses and hardware(from NeedsWings).
Torqued inside out pattern from 7 to 8ft/lbs.
No leakage and looks hawt!
Enjoy your weekend and your XF!
Thanks to Rob at NeedsWings for hardware
Shine and sparkle of fresh valve covers is outstanding
Cheers!
Last edited by CaughtInaXF; 03-11-2023 at 11:45 AM.
The following users liked this post:
Ljcollingham (03-14-2023)
The following users liked this post:
CaughtInaXF (03-12-2023)
The following 3 users liked this post by dcskmail:
The following users liked this post:
richb55 (03-11-2023)
Re: What did you do to your Crossfire today?
Cheers
The following users liked this post:
CaughtInaXF (03-12-2023)