What did you do to your Crossfire today?
Re: What did you do to your Crossfire today?
I just finished replacing mine too but the foam is a gloss black. I purchased this online someplace and it came with a break off disposable blade and a roller. What I did was cut it to fit, even cut slits to fit factory hold down tabs, then cut an X in the backing put it in place then slid my hand under and pulled the backing off in 4 quarters, then used the roller. Will also post some pics when I finish everything.
Re: What did you do to your Crossfire today?
Lookin good there ! !
how do you like those handle covers ? the plastic ones i had were a bit sharp on the inside edges, it bugged me so i went with the stainless steel door handle bowls instead.
from here ..
CHROMETEC. High Quality Tuning für Mercedes-Benz
how do you like those handle covers ? the plastic ones i had were a bit sharp on the inside edges, it bugged me so i went with the stainless steel door handle bowls instead.
from here ..
CHROMETEC. High Quality Tuning für Mercedes-Benz
Re: What did you do to your Crossfire today?
Had to replace top post lead to battery as screw threads were worn out; found primary negative cable with some corrosion. Cleaned it off and mounted new lead and it looks cleaner, nicer and probably works better too. Small job but rewarding. Next up ordering chrome door handles thanks to maggy55...and doing the oil can thingy.
Re: What did you do to your Crossfire today?
Replaced the cabin air filter. The old one was clogged full of leaves and dirt. Not sure how/why.
You will find tons of leaves and debris underneath clogging the 4 drains.
Use a coat hanger to GENTLY clear the drains ( don't knock off the rubber tubes underneath )
Eventually this can cause water to pour in through the fan hole and soak your amplifier and TCM,
not to mention ruining the fan motor and resistor board..
Re: What did you do to your Crossfire today?
Finished putting the car back together after this years mods; painted hood and bumper again, refinished wheels, made new wing emblems and wheel cap covers to match, redid cannards and front splitter, made diffusers for the rear and fixed a few trim issues inside. My first show is Saturday, so I will take some pics then and post them..
Re: What did you do to your Crossfire today?
Finished putting the car back together after this years mods; painted hood and bumper again, refinished wheels, made new wing emblems and wheel cap covers to match, redid cannards and front splitter, made diffusers for the rear and fixed a few trim issues inside. My first show is Saturday, so I will take some pics then and post them..
Join Date: May 2017
Location: Southern Maryland
Age: 61
Posts: 89
Likes: 0
Received 1 Like
on
1 Post
Re: What did you do to your Crossfire today?
You will need to remove the wiper arms and the plastic cowl.
You will find tons of leaves and debris underneath clogging the 4 drains.
Use a coat hanger to GENTLY clear the drains ( don't knock off the rubber tubes underneath )
Eventually this can cause water to pour in through the fan hole and soak your amplifier and TCM,
not to mention ruining the fan motor and resistor board..
You will find tons of leaves and debris underneath clogging the 4 drains.
Use a coat hanger to GENTLY clear the drains ( don't knock off the rubber tubes underneath )
Eventually this can cause water to pour in through the fan hole and soak your amplifier and TCM,
not to mention ruining the fan motor and resistor board..
What about using a shop vac, would that work? Or is it too large or powerful?
Join Date: May 2017
Location: Southern Maryland
Age: 61
Posts: 89
Likes: 0
Received 1 Like
on
1 Post
Re: What did you do to your Crossfire today?
Where can I find this cupholder? I've just located plastic looking ones and this looks a little nicer from the photos. I suspect it's still plastic but it looks good.
Re: What did you do to your Crossfire today?
I just replaced all four Hankook Ventus V12 evo K110 tires after 16,400 miles. The back tires were down to the wear bars and were pretty evenly worn. The front tires still had a good amount of tread on them, but I replaced them anyway. The new tires are Michelin Pilot Sport A/S 3. I also had my OEM wheels refurbished and they look great.
Re: What did you do to your Crossfire today?
I just resoldered the RCM and wish I had done it sooner, was stranded after the car died suddenly on the road. Two cel warnings pointing to the AIR system and I waited as I didn't come back on for a while. Live and learn! She's driving good again now. Just ordered the Eurotune May special! That's next.
Join Date: May 2017
Location: Southern Maryland
Age: 61
Posts: 89
Likes: 0
Received 1 Like
on
1 Post
Re: What did you do to your Crossfire today?
I did the sticky key fix, installed a new Kenwood stereo, checked the RCM solder and cleaned under the cowl today. Yesterday I picked it up after a Auto glass installer rebonded my back glass after it fell out. I been through a fair amount since getting it a week ago.