What did you do to your Crossfire today?
Re: What did you do to your Crossfire today?
Adrian_X aka Adrian came to the house and installed my LED strips for Rear Brake, Tail lights and turn signals
click >>>Tail lights question, possible LED mod
Lights on /No Brakes
Lights On / With Brakes
Lights On in Garage
click >>>Tail lights question, possible LED mod
Lights on /No Brakes
Lights On / With Brakes
Lights On in Garage
Re: What did you do to your Crossfire today?
Reinstalled front clip after being repainted and license plate holes filled, LED lights installed (All around), clear side markers installed, Zunsport upper and lower grilles installed, last but least, front and rear chrome wing medallion are now color matched with Andrews emblems.
http://www.ebay.com/itm/Vetrap-SELF-ADHERING-adhesive-Bandage-First-Aid-Medical-Horse-Wrap-Tape-COLORS-/171416749106?var=470754829379&hash=item27e93c0432
I also wrapped that center support brace with it . . .
Re: What did you do to your Crossfire today?
Changed the oil, emptied the oil catch can, changed the supercharger oil, replaced the fog light housing on both sides, replaced the passenger side headlight HID ballast, fixed the fog light cap thingy (again x 4), added some Tail of the Dragon graphics and gave her a wash. A lot of things built up over time so glad to get it all done.
Join Date: Nov 2007
Location: Las Vegas, NV
Age: 78
Posts: 297
Likes: 0
Received 10 Likes
on
9 Posts
The following users liked this post:
×Crossfire1× (03-19-2023)
Re: What did you do to your Crossfire today?
Lookin' Good !! If you want to "black out" the hose clamps holding the air filters, I used this:
Vetrap Self Adhering Adhesive Bandage First Aid Medical Horse Wrap Tape Colors | eBay
I also wrapped that center support brace with it . . .
Vetrap Self Adhering Adhesive Bandage First Aid Medical Horse Wrap Tape Colors | eBay
I also wrapped that center support brace with it . . .
Re: What did you do to your Crossfire today?
Hmm, never thought about doing that but I agree it would look better. I might look into removing it later today.
20150831_133622_zpsnlad2tws.jpg
Last edited by HOT FIYA; 08-31-2015 at 01:45 PM.
Join Date: Apr 2015
Location: Cochran, Georgia
Age: 28
Posts: 292
Likes: 0
Received 4 Likes
on
3 Posts
Join Date: Apr 2015
Location: Cochran, Georgia
Age: 28
Posts: 292
Likes: 0
Received 4 Likes
on
3 Posts
Re: What did you do to your Crossfire today?
I finished dipping the door handles after I got news of starting my new job tomorrow! I'm excited for the raise in pay and my car will be enjoying it too in the near future. Here she is showing off her newly done front emblem, side markers, and door handles.. along with the daily in the background. All we're missing is the windshield surround now. That should be done soon. I have had a great day and hope everyone else has too!!
The following users liked this post:
×Crossfire1× (03-19-2023)
Join Date: Apr 2015
Location: Cochran, Georgia
Age: 28
Posts: 292
Likes: 0
Received 4 Likes
on
3 Posts
Re: What did you do to your Crossfire today?
Ordered some NeedsWings intake manifold gaskets today. I'm removing the intake manifolds this week to be painted + have some bungs mounted for my boost gauge. It'll need new gaskets upon removing the manifolds so I figured I might as well upgrade them to NeedsWings units. Same ones they include with their tweaked manifolds.
Unrelated, but I wish Samco Sport made a coolant hose kit for our cars.
Unrelated, but I wish Samco Sport made a coolant hose kit for our cars.
Re: What did you do to your Crossfire today?
The company Vertical Doors have done hundreds of cars but mine is a mess passenger side the door does not fit right when you close it hits door lam the window is not align right as it doesn't fit in the rubber channel if it rains it will get in I wont even open the passenger door as it will flake paint off the door and door jam. the driverside the fender is out of alignment the fender stiks out the lower panel is out of place, I find it hard that with all of the hundreds they have done no one even looked at it, they offered to fix it but 2 weeks out so I cnt use the passenger door. A lot of money wasted.
The following users liked this post:
×Crossfire1× (03-19-2023)
Re: What did you do to your Crossfire today?
Put a power window regulator on the passenger side, not too hard but time consuming. The hardest part is the top right nut as you're looking at the door, a socket end wrench doesn't move very far when it's on the nut. The good thing is you only have to loosen it, the bracket it's in is a slot instead of a hole. Pics showing the bolt and wrench, and about where it's located, it's actually a little higher than I show in last pic. It would be nice to have a hole through the rectangular flat spot.
Join Date: Apr 2015
Location: Cochran, Georgia
Age: 28
Posts: 292
Likes: 0
Received 4 Likes
on
3 Posts
Re: What did you do to your Crossfire today?
The company Vertical Doors have done hundreds of cars but mine is a mess passenger side the door does not fit right when you close it hits door lam the window is not align right as it doesn't fit in the rubber channel if it rains it will get in I wont even open the passenger door as it will flake paint off the door and door jam. the driverside the fender is out of alignment the fender stiks out the lower panel is out of place, I find it hard that with all of the hundreds they have done no one even looked at it, they offered to fix it but 2 weeks out so I cnt use the passenger door. A lot of money wasted.
The following users liked this post:
×Crossfire1× (03-19-2023)
Re: What did you do to your Crossfire today?
Those lower billets mount to the oem grilles .. just a heads up there..
Join Date: Jul 2015
Location: Pittsburgh, PA
Age: 60
Posts: 945
Likes: 0
Received 6 Likes
on
6 Posts
Re: What did you do to your Crossfire today?
After I had the Flowmaster super 44 muffler installed I was getting a bit of a drone so I bought some Velostar foam high density so I installed 1 sheet of the 1/2 inch and another sheet of 1/4 inch very high density under the pad in the trunk made a BIG difference.